GPIO protocol
Supported device types and versions
Communication line configuration
Communication station configuration
I/O tag configuration
Literature
Changes and modifications
Document revisions
Supported device types and versions
Protocol supports communication via GPIO (General Purpose I/O) interface on Raspberry PI and computers built on a RPI Compute Module. Currently supported are:
- Raspberry PI (version 2 and 3) based on pigpio library
- Techbase NPE-X500 M3 (DIN-mounted industrial computer built on RPI Compute Module 3 with optional industrial inputs and outputs)
The communication was tested with Raspberry PI (version 3) and NPE-X500-M3-MAX-3G.
The protocol allows reading of digital and analog inputs (in case of NPE-X500 also a value of user button), writing to digital outputs (for NPE-X500 also setting relay outputs, working with user LEDs and a buzzer).
Communication line configuration
- communication line category: API.
- By default, a single line with a single station is configured for one device. If there is a need to stop communication with selected inputs/outputs, there may be several stations on one line. Due to the load distribution or for the rapid reading of the digital inputs, several lines with one or more stations per-line can be configured.
Communication line parameters
Communication line - configuration dialog box - the Protocol parameter tab.
Parameters defined in the field have effect on some optional protocol parameters. There can be defined the following line protocol parameters:
Table 1
| Full name | Description | Units / size | Default value |
|---|---|---|---|
Device Type | Type of device. Currently supported are::
| - | Raspberry PI |
Library Name | Name of library with communication functions for a particular device. The used values are:
| - | - |
Read Delay Ms | Delay after one reading of the values of all I/O tags. Using this parameter, it is possible to control the reading frequency more finely than using the polling parameters in the configuration of time parameters of the station. | ms | 1 |
Communication station configuration
- Communication protocol: GPIO Protocol.
- Station address: n/a.
I/O tag configuration
Possible I/O tag types: Ai, Ao, Ci, Co, Di, Do.
The address format of the I/O tag depends on the device type.
I/O tag addresses for Raspberry PI
In the following table, id defines the number of ping in BCM (Broadcom) numbering.
Following image copied from http://pinout.xyz shows the BCM pin numbering on the GPIO connector:
| Address | Description | I/O tag type | Examples |
|---|---|---|---|
DI,id | The GPIO pin will be configured as a digital input. If the voltage of 3.3V is applied to it, the value of input will be 1. If 0V (ground) voltage is applied to it, the value of input will be 0. | Di, Ci, Ai | DI,25 DI_UP,24 |
DO,id | The GPIO pin will be configured as a digital output. If a value of 1 is written to it, the output will be 3.3V. If 0 is written, output voltage will be 0V (ground). | Dout, Co, Ao | DO,24 |
| PWM,id | The GPIO pin will be configured as PWM (pulse width modulation) output. It is then possible to write values 0-255 controlling the width of pulse from fully off to fully on. | Dout, Co, Ao | PWM,12 |
| REVISON | The revision of the hardware (the number from the "Revision" line from the /proc/cpuinfo file. For example, for RPI 3 in this file is the row "Revision : a02082" and the revision value is 10494082 (after conversion from hexadecimal system). | Ci | REVISON |
I/O tag addresses for NPE-X500
In the following table, id defines the number of input/output (e.g. DI, DO, AO). The number of inputs and outputs depends on the particular model. The notes are referring to the NPE-X500-M3-MAX-3G that was tested.
Note 1: Output points whose addresses contain _BUF use a buffered writing. This allows the values of such objects not only to be written, but also to be read, which can be useful, for example, after the start of the KOM process.
Note 2: With the tested model, the reading of the digital input took less than 1 ms, while the reading the analog input took approximately 20 ms.
| Address | Description | I/O tag type | Examples |
|---|---|---|---|
DI,id | Digital input (DI) | Di, Ci, Ai | DI,1 DI,2 |
DO,id | Digital output (DO). If buffered (DO_BUFF), the value is also read (during startup and periodically). | Dout, Co, Ao | DO,1 |
| DIO,id DIO_BUF,id | Digital input/output. Based on I/O tag type, the GPIO port is configured as input (Di, Ci, Ai) or output (Dout, Co, Ao). | Input: Di, Ci, Ai Output: Dout, Co, Ao | DIO,2 DIO_BUF,3 |
| RELAY,id RELAY_BUF,id | Relay output. If buffered (RELAY_BUFF), the value is also read (during startup and periodically). | Dout, Co, Ao | RELAY,1 RELAY_BUF,2 |
| AI,id | Analog input (AI). | Ci, Ai | AI,1 |
| LED,id LED_BUF,id | LED output. If buffered (LED_BUFF), the value is also read (during startup and periodically). | Dout, Co, Ao | LED,1 LED_BUF,2 |
| BUZZER BUZZER_BUF | Buzzer. If buffered (BUZZER_BUFF), buzzer status is also read (during startup and periodically). | Dout, Co, Ao | BUZZER BUZZER_BUF |
| BUTTON BUTTON_BUF | User button status. | Di, Ci, Ai | BUTTON |
Literature
Changes and modifications
Document revisions
- Ver. 1.0 - August 30th, 2018 – Document created
Related pages: