Page tree

Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

...

Full nameMeaningUnitDefault value
Anchor
cmdc
cmdc
Command Confirm
Confirmation of control ASDUs.
If CMDC=0, the process D2000 KOM is not waiting for confirmation of control ASDUs from the partner station using backward sending ASDU with other CauseOfTransmission, ASDU is consider to be confirmed when a packet containg corresponding ReceiveSequenceNumber is received.
If CMDC=1, the process D2000 KOM is waiting for confirmation with CauseOfTransmission=7 (Activation Confirmation).
If CMDC=2, the process D2000 KOM is waiting for confirmation with CauseOfTransmission=10 (Activation Termination).
If CMDC=3, the process D2000 KOM is waiting for confirmation with CauseOfTransmission=7 or 10 (if both of them are received, just the first of them is taken into account).
Having received the corresponding confirmation means that writing is finished (the Transient attribute of written value is evaluated and the WTn timeout stops elapsing).
If there is received confirmation with other CauseOfTransmission as the process D2000 KOM expect for, it will be ignored.
Writing is successful if received ASDU contains the P/N bit set to 0. Otherwise, writing is unsuccessful.
The value from a received ASDU is backwardly written into the corresponding I/O tag and is sent to the system. E.g. if an ASDU of type 50 (short floating point) with the value of 1200.0 is sent and the partner station sends an ASDU of type 50 as reply, P/N bit=0, value of 999.0 (e.g. due to physical limitations of the given parameter), the the value is to be send by the process D2000 KOM to the system.
-3
Anchor
dbgi
dbgi
Debug Input
It is a mask for a debug level of the input data.
A meaning of the bits:
  • 1. bit - number of points received within General Interrogation
  • 2. bit - a received values of I/O tags
  • 3. bit - balanced mode: Interrogation command was received
0 .. 2550
Anchor
dbgo
dbgo
Debug Output
It is a mask for a debug level of the output data.
A meaning of the bits:
  • 1.bit - balanced mode: a number of points sent within General Interrogation
  • 2.bit - it shows a sent values of I/O tags
0 .. 2550

Anchor
iccpf
iccpf
ICCP compatible flags

It allows a flag mapping which is compatible to Sinaut Spectrum ICCP OPC communication. For more information see ICCP compatible flag mapping.YES/NONO

Anchor
if
if
Ignore Flagged

The parameter allows to specify the flags of values (data ASDU 1-40), which - if set - will cause the value to be discarded. The parameter was implemented when it was necessary to filter out the "Non-topical" flag values that came from the communication partner.

The mapping of individual flags from ASDU to A..H flags is as follows:

  • A - Overflow (OV) - ASDU 5-14, 20, 32-36
  • B - no mapping (according to standard this bit should be 0)
  • C - no mapping (according to standard this bit should be 0)
  • D - Elapsed Time Invalid (EI): ASDU 17-19, 38-40
  • E - Blocked (BL) - ASDU 1-14, 17-20, 30-36, 38-40
  • F - Substituted (SB) - ASDU 1-14, 17-20, 30-36; Counter overflow (CY) - ASDU 15, 16, 37
  • G - Non-topical (NT) - ASDU 1-14, 17-20, 30-36; Counter adjusted (CA) - ASDU 15, 16, 37
  • H - Invalid (IV) - ASDU 1-20, 30-40
A..H-
Anchor
iua
iua
Ignore Unknown Addresses
If IUA=TRUE, the process D2000 KOM will not show an error on its console or write it into log files in case that incoming value has the address not matching any of the addresses of I/O tags defined in the D2000 system.-False
Anchor
icci
icci
Interrogation Covers Counter Interrogation
As a reply to Interrogation, there are also sending ASDU 15,16,37 (Integrated Totals), which are standard requested by ASDU 101 [Counter Interrogation].-True
Anchor
k
k
K (max outstanding I APDUs)
Sending window size i.e. packet quantity, which is sent by the process D2000 KOM without receiving a confirmation (S-frame or I-frame). According to the standard, the default value is 12.-12
Anchor
nf
nf
No Flags
If the parameter is True, then the status bit of incoming ASDUs is ignored and not saved into the flags FA...FH. Flags of output I/O tags are also ignored and they not set the status bit.-False
Anchor
oic
oic
Order of IC
Order for sending ASDU 100 [Interrogation Command] when the station initializes to communicate or when creating a new station. If OIC<OCIC, ASDU 10 will be send before ASDU 101. If OIC=0, ASDU 100 will not be sent. The parameter can be set extra for each station.-1
Anchor
ocic
ocic
Order of Counter IC
Order of sending ASDU 101 [Counter Interrogation Command] when initializing the connection. OCIC<OIC, ASDU 101 will be sent before ASDU 100. If OCIC=0, ASDU 101 will not be sent. The parameter can be set extra for each station.-0
Anchor
pcnt
pcnt
Ping Count
Number of repetitions, after which the IP address not responding to ping is to be known as non-functional.
See the parameter PTO.
-3
Anchor
pto
pto
Ping TimeOut
If the parameter is other than zero, then defines the timeout (in milliseconds) of server response for ping (ICMP echo) packet. In the background, the process D2000 KOM sends ping packets to all defined IP addresses. If some of the addresses does not respond for PCNT-times, it is designated as non-functional and connection is terminated. If the parameter PTO= 0, sending ping packet to IP addresses is disabled.-0
Anchor
psd
psd
Post Start Delay
When initializing the connection, delay between receiving StartDT Con response and sending Interrogation Command and/or Counter Interrogation Command.ms0

Anchor
ssn
ssn
Send

Ssequence

Sequence Number

Initial SSN. According to the standard, after establishing the connection the SSN is set to 0, other than zero could be appropriate e.g. for testing.-0
Anchor
spsh
spsh
Server Port, Server Host
The port number and IP address of the interface, where the process D2000 KOM is to be listening. If both the parameters are defined, the process D2000 KOM is working as passive (is waiting for connecting Sinaut clients). If the process should listen on all network interfaces, there must be set SH=ALL.-
Anchor
sko
sko
Standby Keep Open
If True, after changing the status of process D2000 Server (the process D2000 KOM is connected to) from Hot into Standby state (redundant system), connection with partner will not be closed.-True
Anchor
st_ce
st_ce
Station Communication Error
Number of unsuccessful attempts to connect after communication breakdown. The station status is changed into the state St_CommErr after reaching the number. For redundant lines, the communication must be either failed for both TCP connections or a TCP connection with standby-server must be functioning (see the parameters ICF3 and IT), i.e. data from the server are ignored.-2
Anchor
st_he
st_he
Station Hard Error
Number of unsuccessful attempts to connect after communication breakdown. The station status is changed into the state St_HardErr after reaching the number. For redundant lines, communication must be either failed for both TCP connections or working a TCP connection with standby-server must be functioning (see the parameters ICF3 and IT), i.e. data from the server are ignored.-5
Anchor
srcs
srcs
Strict Redundancy Connection Signalisation
Number of TCP connections, which must be opened so that the line could be considered as OK. There are 4 connections (2x Sinaut, each of them has 2 network addresses).-4
Anchor
tki
tki
Tcp Keep Init
The parameter is implemented for use on OpenVMS platforms only. If it is other than zero, then defines the timeout (in seconds) for opening a new connection to server. For OpenVMS, the default value is 75 seconds, for Windows it is 20 seconds.-0
Anchor
tnd
tnd
TCP NoDelay
TND parameter sets a low-level parameter of TCP_NODELAY sockets which switch off a default packet linking.

Anchor
w
w
W (ack after receiving W APDUs)
Quantity of received packets, after which the process D2000 KOM sends an S-frame confirmation. According to the standard, the default value is 8. There must be true W < K, the standard recommends W = 2/3 * K.-8
Anchor
wt1
wt1
Wait Timeout T1
Timeout for receiving the confirmation of a I-frame sent (either the confirmation within the I-frame or the S-frame itself) or a U-frame. If the process D2000 KOM does not get the confirmation in the time WT1, it closes the TCP connection. According to the standard, the WT1 default value is 15000 ms.ms15 000
Anchor
wt2
wt2
Wait Timeout T2
Timeout for sending the confirmation of a I-frame received. WT2 < WT1. If another I-frame (which confirms the I-frame received) is not sent in the time WT2 since the I-frame was received, so the process D2000 KOM sends an S-frame confirming the received I-frame to the partner. According to the standard, the WT2 default value is 10000 ms.ms10 000
Anchor
wt3
wt3
Wait Timeout T3
Timeout for sending test frames (U-frame TEST ACT). If no data are sent in any direction for a long time, an U-frame TEST ACT will be sent to the process D2000 KOM after expiration of the WT3 time and there is expected (in the WT1 time after sending) receiving a U-frame TEST CON. If the WT3 on the partner side is set to a lower value, it sends the test frames and the process D2000 KOM replies to them. According to the standard, the WT2 default value is 20000 ms. Setting the value to 0 disables sending test frames.ms20 000
Anchor
wtn
wtn
Wait Timeout N
Timeout for receiving the confirmation of a value sent. Receiving e.g. S-frame with RSN (Receive Sequence Number) confirming, that the other party received previous I-frame doesn't mean, that the I-frame was processed. In the WTn time, the process D2000 KOM waits for receiving the response (e.g. after sending ASDU with TypeIdentificator=45 [Single Command] with CauseOfTransmission=6 [Activation] there is expected receiving Single Command with CauseOfTransmission=7 [Activation Confirmation].
After the expiration of the WTn time, the process D2000 KOM closes the TCP connection.
ms60 000

...